Shop Industrial Adhesives
Cyanoacrylates
Cyanoacrylates, universally known as superglues, are the fastest way to make a strong bond between two small, well-fitting parts. The family is older than most people assume, and the original is still in production: Permabond holds the licence for Eastman 910, the very first cyanoacrylate, and sells it to this day. The Permabond range is the core of what we stock.
How cyanoacrylates work
Bonds: Most plastics · Rubbers · Metals · Wood · Ceramics
A cyanoacrylate cures by reacting with the trace moisture already present on almost every surface. That is why it sets in seconds without heat, mixing or pressure, and it is also why the joint has to be close-fitting: with no moisture and no surface to react against, a thick gap stays liquid in the middle.
The resulting bond is hard and very strong in tension and shear. Rigidity cuts both ways. A standard grade is brittle under impact and peel, and many grades are not at their best in water or at high temperature. Toughened, flexible and water-resistant grades are made specifically to deal with those limitations, so a cyanoacrylate that failed on a previous job is often the wrong grade rather than the wrong chemistry.
Choosing a grade
Three things decide the grade. Viscosity, from water-thin wicking grades that draw into an assembled joint up to gels that will not run on a vertical surface or soak into a porous one. Substrate, which sets whether you need a general-purpose grade, a rubber and plastic grade, or a primer. And cured performance: impact resistance, temperature range and resistance to water or solvents.


Epoxies
Epoxy is what you reach for when the joint has to carry real load, fill a gap, or survive an environment that would destroy anything else.
How epoxies work
Bonds: Metals · Composites · Glass · Ceramics · Most plastics · Concrete
Most epoxies are two parts: a resin and a hardener that cure when mixed in the correct ratio. The two components cross-link into a dense three-dimensional network, which is where the strength, the toughness and the chemical resistance come from. Because the reaction does not depend on air, moisture or the gap closing up, epoxy cures right through a thick joint, which makes it the family of choice for gap filling and for bonding parts that do not fit together perfectly.
One-part epoxies are pre-mixed and cure with heat instead. That is a real advantage in production: the powder coating industry uses one-part epoxy because it holds the parts together through handling and then cures in the same oven pass that bakes the powder, saving an entire process step.
What epoxies are used for
Epoxies bond and seal structural assemblies, pot and encapsulate electronics, repair castings and housings, and replace welding where heat would distort a part, discolour a finish or damage what is inside it. Grades are available with FDA compliance for food contact and WRAS approval for contact with drinking water.
Structural acrylics
Structural acrylics do exactly what the name says: they make permanent, load-bearing assemblies.
How structural acrylics work
Bonds: Metals · Most plastics, including untreated nylon, PE and PP · Composites
The common industrial form is a two-part, no-mix system. Adhesive goes on one surface and activator on the other, the parts are brought together and clamped, and cure begins where the two meet. Nothing has to be measured, mixed or dispensed through a static mixer, which makes it quick and hard to get wrong on a production line.
Structural acrylics are tough rather than brittle, hold up well to impact and peel, and tolerate oily, unprepared and mismatched surfaces better than epoxies or cyanoacrylates. Some grades bond untreated nylon, polyethylene and polypropylene, the low-surface-energy plastics that normally need a primer or a flame or plasma treatment before anything will stick to them.
What structural acrylics are used for
Typical work includes bonding aluminium panels and sidings to truck and trailer bodies, fixing signage to walls and frames, assembling shower and glazing enclosures, and any metal-to-plastic joint where the two materials expand at different rates and a rigid adhesive would eventually crack.


Anaerobic adhesives and sealants
Anaerobic means without air, and that is the whole trick: these liquids stay liquid in the bottle, in contact with air, and cure only once they are shut inside a metal joint.
How anaerobics work
Bonds: Metal threads · Metal cylindrical fits · Metal flanges
Two conditions have to be met for an anaerobic to cure. Air has to be excluded, which happens automatically when a bolt is done up or a bearing is pressed home. And metal ions have to be present, because they start the reaction. Most steels supply them readily. Stainless steel, aluminium, plated, anodised and plastic surfaces are described as inactive, and need a surface activator applied first or the adhesive will sit there uncured.
Threadlockers
A threadlocker fills the clearance between the male and female threads and cures solid, so the fastener cannot vibrate loose and the thread is sealed against corrosion. This is more reliable than a spring or lock washer, which depends on maintaining tension. Strengths run from low, for small screws and adjustment settings you still want to move, through medium, which comes apart with hand tools, up to high strength, which needs heat to release and effectively makes removal without proper tools impossible.
Thread sealants
A thread sealant seals a tapered pipe thread against pressure, and does the job better than tape or hemp. It fills the whole thread helix rather than bridging it, it will not shred and contaminate the system, and until it cures the fitting can still be backed off and re-aligned, which tape does not allow without starting again.
Retaining compounds
Retaining compounds fill and bond cylindrical fits: bearings on shafts, bushes in housings, gears, pulleys, studs and dowels. Filling the clearance spreads the load over the whole engaged surface instead of a few high spots, which raises the load the joint can carry, stops fretting corrosion, and can bring a worn housing back into service instead of scrapping it.
UV and light cure adhesives
Light cure adhesives solve a problem the other families cannot: they let you control exactly when curing starts.
How light cure works
Bonds: Glass · Clear plastics · Metals (with one transparent side)
These adhesives contain photoinitiator molecules that are stable in the dark and split into highly reactive free radicals when the right wavelength of light reaches them. Those free radicals set off polymerisation, and cure is essentially instant. Until the light is switched on, the adhesive stays liquid indefinitely, so parts can be dispensed, assembled and aligned at leisure and then fixed in seconds.
Because the light has to reach the adhesive, at least one of the two parts must be transparent to the curing wavelength. Most light cure adhesives are optically clear, which is why they dominate glass assembly, display and optical bonding, medical device assembly and electronics work where a visible bond line would be a defect. Cure on demand also suits high-volume production, where the bottleneck is usually waiting for a joint to set.


Primers, activators and dispensing
Two jobs fail far more often than the adhesive itself: preparing the surface, and getting the right amount of adhesive into the right place.
Surface preparation
An adhesive bonds to whatever is on the surface, and on most parts that is oil, release agent, oxide or dust rather than the material itself. Degrease first, abrade where the process allows it, and degrease again. This single step recovers more failed bonds than changing product ever does.
Primers and activators
A polyolefin primer changes the surface chemistry of low-surface-energy plastics such as polyethylene, polypropylene, PTFE and silicone, so a cyanoacrylate will hold on materials that otherwise reject it. A surface activator does the opposite job for anaerobics, supplying the metal ions that inactive surfaces such as stainless steel, aluminium and plated finishes do not provide. Activators also speed the cure of cyanoacrylates and let them bridge a slightly larger gap.
Dispensing equipment
Applicators, dispensing guns, static mixer nozzles, needles, bottles and curing lamps control how much adhesive goes on and where. For anything running at volume, consistent dispensing is what makes the results consistent, and it stops the far larger cost of adhesive being wasted or squeezed out of the joint.
Choosing an adhesive
Work through the joint, not the product list: the materials, the gap between them, what the joint has to survive, and how fast you need it to set.
What we will ask you
- both materials being bonded, named specifically, because “plastic” covers everything from easy to impossible
- the gap between the parts, and whether they can be clamped
- the load on the joint, and whether it is tension, shear, peel or impact
- service temperature, and exposure to water, chemicals, oil or UV light
- how fast it has to fix and how fast it has to reach full strength
- the production process: hand assembly or line, and any food, water or medical approvals needed.
Which family suits the job?
| Family | Best for | Gap fill | Set speed | Watch out for |
|---|---|---|---|---|
| Cyanoacrylate | Small, close-fitting parts | Poor | Seconds | Impact, peel, water |
| Epoxy | Structural joints, gap filling | Excellent | Minutes to hours | Mix ratio, pot life |
| Structural acrylic | Tough joints, awkward substrates | Good | Minutes | Odour, clamping needed |
| Anaerobic | Threads, bearings, flanges | Good (metal fits) Poor | Minutes to hours | Inactive metals need activator |
| UV cure | Glass, optics, clear assemblies | Moderate | Seconds under light | One part must pass light unless dual cure |
Getting it right first time
A sample and a test piece will tell you more than any datasheet. If you are manufacturing, talk to us before you commit to a product: we can usually arrange a sample of the grade we think fits, and it is far cheaper to test a joint than to recall an assembly.
Frequently asked questions
Can you bond silicone, PTFE or polypropylene?
Yes. These are low-surface-energy materials that normally reject adhesive. A polyolefin primer changes the surface so a cyanoacrylate will hold, and some structural acrylics bond untreated nylon, polyethylene and polypropylene without any primer at all.
Can an epoxy really replace welding?
In many assemblies, yes. Bonding puts no heat into the part, so there is no distortion, no discolouration of coloured stainless or anodised aluminium, and no damage to anything sensitive inside. It also joins materials that cannot be welded to each other. The joint has to be designed for adhesive, with enough overlap area and load in shear rather than peel.
Why does superglue never work as well as I expect?
Usually one of three reasons. The product is a consumer-grade adhesive rather than an industrial one. The joint has too big a gap, and cyanoacrylates need a close fit. Or the material is a low-surface-energy plastic such as polyethylene or polypropylene, which needs a polyolefin primer first.
My threadlocker did not cure. What went wrong?
Almost always an inactive surface. Anaerobics need metal ions to cure, and stainless steel, aluminium, plated, anodised and plastic threads do not supply enough. Apply a surface activator first. Check too that the fastener was actually tightened, because the adhesive only cures once air is excluded.
Is thread sealant better than PTFE tape?
For most pressure applications, yes. Sealant fills the whole thread rather than bridging it, cannot shred and contaminate the system, and lets you back the fitting off to align it before it cures. Tape has to be rewrapped if you move the joint.
I have found a product online that you do not stock. Can I get it?
Sometimes. We buy in box quantities, so the smallest order we could sell you would be a full box. If you are a manufacturer, talk to us — we can usually arrange a sample and find an equivalent from the range we carry.
How should I store adhesives?
Cool and dry, in the original container with the cap on. Cyanoacrylates last considerably longer refrigerated, and should be brought back to room temperature before opening so condensation does not form in the bottle. Check the shelf life on the container; an out-of-date adhesive is the cheapest thing to replace on any job.
